POSCO PEAK smart home remote control switch 220V lighting 2/3/4/8 touch control delay wireless segmentation device three-touch
The wireless remote light switch of this model can switch four electrical circuits independently of each other.
The control units can be installed in different rooms.
Load power in the circuit up to 1000W.
Remote lighting control is carried out using two-touch remote controls.
To control lighting, simply touch the sensor zone of the remote control.
The peculiarity of this kit is that each channel has its own control unit, which in turn makes it possible to install the units in different places and not to lead the wiring to one point, as it should be done in other functionally similar sets.
The receiver of the radio signal is installed in the junction box or in the immediate vicinity of the consumer, for example, over a false ceiling.
Remote switch can be used in an apartment, a country house, a sales hall, an office.
Posco Peak has been engaged in the production of remote switches with original design for several years.
The controllable unit is much smaller in size compared to similar models, which allows it to be installed in compact designs.
Attention: the remote unit must be connected in series with the domestic key switch, as indicated in the diagram.
A neutral wire is required to connect the remote switch.
How it works: when entering the room, including the key switch, all relevant load lines are turned on.
Further lighting control can be done from the remote control.
If the key switch is turned off, the control from the panel will not work, because the circuit is open.
Remote switch has proven itself in suspended, stretched, multi-level ceilings and chandeliers.
It can be used to include both basic and decorative lighting.
Remote switch perfectly fits into the office of any manager!
The remote switch is suitable for LED loads: LED light bulbs, LED lamps, chandeliers with LED bulbs, spot LED lighting, etc.
Correspondence of the blocks to the buttons of the control panel:
Button No. 1 supplies voltage to unit No. 1.
Button No. 2 supplies voltage to unit No. 2.
Button No. 3 supplies voltage to unit No. 3.
Button No. 4 supplies voltage to unit No. 4.
Button No. 5 supplies voltage to unit No. 5.
Button No. 6 supplies voltage to unit No. 6.
Button No. 7 supplies voltage to unit No. 7.
Button No. 8 supplies voltage to unit No. 8.
Details of remote control switch, 4 or 8-point intelligent control system, remote control, touch screen. Turn off the remote light switch.
Ammeter Switch Remote
Features
Used to control the opening and closing of electrical equipment.
Remote control up to 50 meters
4 or 8 independent working cycles Can control 4 or 8 points.
No need to wiring between the light bulbs and the remote switch is not hot.
Comes with switch. When turned on, there will be a warning LED.
Up to 1,000 watt bulbs and 300 watt LED bulbs.
Specifications:
Product Name: POSCO smart home remote control switch 220V four split wireless touch lamp controller PY2-4A
Model: PY-1E or PY2-A
SKU: PO931HLAA7633FANTH-15118235
Power source: Corded Electric
Size (cm): 33 * 5 * 18
Total blocks: 4 or 8 pcs.
Total remotes: 1 or 2 pcs.
Number of lines in the block: 1
Supply voltage: ~ 220 V
Modes of operation: with fixation
Max. Controlled load voltage: ~ 220V
Maximum load current: 4.5 A
Maximum power of controlled load: 1000 W
Method of switching: relay
Type of controlled load: active
Housing material: Steel
Radius of the control panel: 20 m
Number of buttons in the remote control: 4 or 8
Used battery: AAA -1.5V
Dimensions of the control unit: 76x43x21 mm
Size of the control panel: 108x45x10 mm
The weight: 4 channel 766g , 8 channel 1 kg
Package:
Remote control unit: 4 or 8 pcs.
Remote control: 2 pcs.
No reviews found