RJTiyanye highly rated 12V 6A intelligent pulse repair charger is a must have for any 12V Lead Acid battery with a rated capacity between 4Ah and 100Ah in cars, motorbikes, boats, agriculture vehicles and small trucks.
The other shell is made of an ABS flame-retardant material which is corrosion-resistant and insulating.
This device supports 110-220V input power supply and has positive and negative battery terminal clips.
This device also automatically detects the ambient temperature and automatically adjusts the appropriate charging voltage according to the detected ambient temperature.
RJ-C 120501A is a networked intelligent multi-mode charger for lead-acid batteries with a nominal voltage of 12 volts and a capacity from 2Ah to 100Ah.
Automatically selects optimal charging parameters.
For old batteries that have not been used for a long time or batteries that are not able to use the charging mode, there is a recovery mode.
1-Once the positive and negative are connected, the LCD screen will light up.
The battery voltage and temperature will be displayed cyclically.
If the positive and negative poles are connected incorrectly, the device will flash "reverse connection" and display EI-I-
2-Once the battery has been connected correctly and then the power supply, the charger will start to charge automatically.
The screen will cycle display of the battery voltage, current, and ambient temperature.
Then choose the charging mode that matches the battery that has been connected (See mode selection on instructions for details).
3-After the charging is complete, the battery power bar on the screen will show as full (100%). It is recommended to continue trickle charging for about 1-2 hours.
At this time, it is in floating charging state until the screen is turned OFF and the charging is completed.
4-After charging is complete, remove the AC plug first, then remove the positive and negative clips.
Mode selection:
Mode selection is only available when the battery and AC is connected to the device.
Each time the mode button is pressed, it switches in the following order "Automobile-Start-Stop-motorcycle-repair"
The car icon is suitable for ordinary cars, agricultural vehicles, trucks and various 12V Lead-acid batteries. (Range: 12V between 15Ah - 100Ah).
The battery icon is suitable for a car battery with start and stop functionality. (Range 10Ah - 100Ah).
The motorbike icon is suitable for all kinds of motorcycles and all kinds of 12V lead-acid batteries. (Range: 12V between 2Ah - 20Ah).
The repair mode (Shield with a plus) icon is for use on batteries that have been idle for a long time, old and unable to charge. See Repair function in the instructions for details.
Note:
There might be little error of size for manual measurement.
Due to different lighting effects and monitor settings, the actual item's color may not exactly reflect the color on
Using the charger:
1. Make sure that the parameters of the battery being charged match the characteristics of the charger
2. Connect the red clip to the positive terminal of the battery, and the black clip to the negative terminal.
3. After connecting the red and black clamps to the battery, the LCD screen will turn on, which will alternately display the battery voltage and ambient temperature.
4. If the connection is incorrect (the red and black clamps are reversed), the words “Reverse connection” and “EI-I-” will flash on the screen.
5. Connect the power cord to a 220 volt source and the charging process will begin automatically.
The display alternates between output voltage, output current and outdoor temperature.
6. Select the charging mode corresponding to the type of battery being charged (for details, see the section on choosing a mode)
7. After the charging process is complete, the charge level indicator will be full (100%) and the display will show “FUL1”. For the best effect, it is recommended to continue the process for 1 hour.
8. After this, it is recommended to first turn off the power cord, and only then disconnect the clamps from the battery terminals.
Selecting charging mode
1. The mode selection can only be changed after connecting the charger to the mains voltage source
2. Pressing the "Mode" key sequentially switches between the modes "Auto" - "Start-Stop" - "Motorcycle" - "Recovery"
3. "Auto" mode - suitable for conventional 12-volt car batteries with a capacity of 15 to 100 ampere-hours.
4. “Start-Stop” mode - suitable for batteries with the “Start and Stop” function, with a capacity from 10 to 100 ampere-hours
5. "Moto" mode is suitable for all types of 12 volt motorcycle batteries, with a capacity of 2 to 15 amp-hours.
6. “Repair” mode - can be used to activate old batteries that have not been used for a long time or are unable to accept a charge.
Indication of conditions of use: winter and summer
1.Winter 0-10 degrees Celsius. Summer - more than 26 degrees Celsius. Normal temperature - 9-25 degrees Celsius (not displayed)
2. The microcontroller automatically detects the ambient temperature and adjusts the charging mode accordingly.
Recovery function
1. Connect the battery to the charger, then connect the mains voltage, press the mode selection key 4 times, “PUL” should appear on the display and the charge level indicator will begin to flash, indicating the charge level.
2. Recommended recovery time: for motorcycle batteries - 5 hours, for car batteries - 8 hours.
In any case, the recovery time should not exceed 24 hours. Pay attention to the battery temperature during recovery.
If the battery becomes hot, you must stop the process immediately!!!
3. If "FUL" appears on the display during recovery mode, the battery is fully charged.
It is recommended to continue the process for 1 hour to get the best effect.
features
A LCD screen display
Voltage detection
Pulse to repair
Temperature detection
Short circuit protection
Over voltage protection
Full power auto stop
Microprocessor controlled
Professional automatic switch mode
For charging AGM,GEL,SLA and Wet batteries
LCD display& pulse repair charge
Overheat, overcharge, short circuit & reverse polarity protection
Maximizes battery life
Specification:
Brand: Ruijie
Material: ABS
Cooling: Fan
Switch mode technology: Yes
Polarity protection: Yes
Output short protection: Yes
Non battery link protection: Yes
Over voltage protection: Yes
Over temperature protection: Yes
Minimum start voltage: 8.0V
Maximum output current: 6 amps
Output cable length: 65cm
Input cable length: 90cm
Output voltage: DC13.8-15.5V
Input voltage: AC110-220V (50-60Hz)
Output current: DC-6A (MAX)
Battery range: 4-100Ah
Thermal protect: 65'C+/-5'C
Efficiency: App. 85%.
Compliant standards: CE,FCC,ROHS,CMA
Size: 147x79x62mm
Package includes:
1 x 12V 6A Intelligent Charger
1 x English Manual
Note:
This charger please for indoor, beware of rain
This charger is for battery capacity between 4AH to 100AH
Do not be carried with the vehicle, prevent shock.
The other shell is made of an ABS flame-retardant material which is corrosion-resistant and insulating.
This device supports 110-220V input power supply and has positive and negative battery terminal clips.
This device also automatically detects the ambient temperature and automatically adjusts the appropriate charging voltage according to the detected ambient temperature.
RJ-C 120501A is a networked intelligent multi-mode charger for lead-acid batteries with a nominal voltage of 12 volts and a capacity from 2Ah to 100Ah.
Automatically selects optimal charging parameters.
For old batteries that have not been used for a long time or batteries that are not able to use the charging mode, there is a recovery mode.
1-Once the positive and negative are connected, the LCD screen will light up.
The battery voltage and temperature will be displayed cyclically.
If the positive and negative poles are connected incorrectly, the device will flash "reverse connection" and display EI-I-
2-Once the battery has been connected correctly and then the power supply, the charger will start to charge automatically.
The screen will cycle display of the battery voltage, current, and ambient temperature.
Then choose the charging mode that matches the battery that has been connected (See mode selection on instructions for details).
3-After the charging is complete, the battery power bar on the screen will show as full (100%). It is recommended to continue trickle charging for about 1-2 hours.
At this time, it is in floating charging state until the screen is turned OFF and the charging is completed.
4-After charging is complete, remove the AC plug first, then remove the positive and negative clips.
Mode selection:
Mode selection is only available when the battery and AC is connected to the device.
Each time the mode button is pressed, it switches in the following order "Automobile-Start-Stop-motorcycle-repair"
The car icon is suitable for ordinary cars, agricultural vehicles, trucks and various 12V Lead-acid batteries. (Range: 12V between 15Ah - 100Ah).
The battery icon is suitable for a car battery with start and stop functionality. (Range 10Ah - 100Ah).
The motorbike icon is suitable for all kinds of motorcycles and all kinds of 12V lead-acid batteries. (Range: 12V between 2Ah - 20Ah).
The repair mode (Shield with a plus) icon is for use on batteries that have been idle for a long time, old and unable to charge. See Repair function in the instructions for details.
Note:
There might be little error of size for manual measurement.
Due to different lighting effects and monitor settings, the actual item's color may not exactly reflect the color on
Using the charger:
1. Make sure that the parameters of the battery being charged match the characteristics of the charger
2. Connect the red clip to the positive terminal of the battery, and the black clip to the negative terminal.
3. After connecting the red and black clamps to the battery, the LCD screen will turn on, which will alternately display the battery voltage and ambient temperature.
4. If the connection is incorrect (the red and black clamps are reversed), the words “Reverse connection” and “EI-I-” will flash on the screen.
5. Connect the power cord to a 220 volt source and the charging process will begin automatically.
The display alternates between output voltage, output current and outdoor temperature.
6. Select the charging mode corresponding to the type of battery being charged (for details, see the section on choosing a mode)
7. After the charging process is complete, the charge level indicator will be full (100%) and the display will show “FUL1”. For the best effect, it is recommended to continue the process for 1 hour.
8. After this, it is recommended to first turn off the power cord, and only then disconnect the clamps from the battery terminals.
Selecting charging mode
1. The mode selection can only be changed after connecting the charger to the mains voltage source
2. Pressing the "Mode" key sequentially switches between the modes "Auto" - "Start-Stop" - "Motorcycle" - "Recovery"
3. "Auto" mode - suitable for conventional 12-volt car batteries with a capacity of 15 to 100 ampere-hours.
4. “Start-Stop” mode - suitable for batteries with the “Start and Stop” function, with a capacity from 10 to 100 ampere-hours
5. "Moto" mode is suitable for all types of 12 volt motorcycle batteries, with a capacity of 2 to 15 amp-hours.
6. “Repair” mode - can be used to activate old batteries that have not been used for a long time or are unable to accept a charge.
Indication of conditions of use: winter and summer
1.Winter 0-10 degrees Celsius. Summer - more than 26 degrees Celsius. Normal temperature - 9-25 degrees Celsius (not displayed)
2. The microcontroller automatically detects the ambient temperature and adjusts the charging mode accordingly.
Recovery function
1. Connect the battery to the charger, then connect the mains voltage, press the mode selection key 4 times, “PUL” should appear on the display and the charge level indicator will begin to flash, indicating the charge level.
2. Recommended recovery time: for motorcycle batteries - 5 hours, for car batteries - 8 hours.
In any case, the recovery time should not exceed 24 hours. Pay attention to the battery temperature during recovery.
If the battery becomes hot, you must stop the process immediately!!!
3. If "FUL" appears on the display during recovery mode, the battery is fully charged.
It is recommended to continue the process for 1 hour to get the best effect.
features
A LCD screen display
Voltage detection
Pulse to repair
Temperature detection
Short circuit protection
Over voltage protection
Full power auto stop
Microprocessor controlled
Professional automatic switch mode
For charging AGM,GEL,SLA and Wet batteries
LCD display& pulse repair charge
Overheat, overcharge, short circuit & reverse polarity protection
Maximizes battery life
Specification:
Brand: Ruijie
Material: ABS
Cooling: Fan
Switch mode technology: Yes
Polarity protection: Yes
Output short protection: Yes
Non battery link protection: Yes
Over voltage protection: Yes
Over temperature protection: Yes
Minimum start voltage: 8.0V
Maximum output current: 6 amps
Output cable length: 65cm
Input cable length: 90cm
Output voltage: DC13.8-15.5V
Input voltage: AC110-220V (50-60Hz)
Output current: DC-6A (MAX)
Battery range: 4-100Ah
Thermal protect: 65'C+/-5'C
Efficiency: App. 85%.
Compliant standards: CE,FCC,ROHS,CMA
Size: 147x79x62mm
Package includes:
1 x 12V 6A Intelligent Charger
1 x English Manual
Note:
This charger please for indoor, beware of rain
This charger is for battery capacity between 4AH to 100AH
Do not be carried with the vehicle, prevent shock.
No reviews found